Product information and Technical condition

• Info_for_buyers_NCC.pdf

Features

• BrandEpiroc SmartROC T35S
• ModelEpiroc SmartROC T35S
• Year Model2019
• VINTMG19SED0182 / 8992 0119 77

Condition

• Overall conditionObject(s) in working condition, but may have minor flaws.
• Usage9142 h

Physical Description

• Weight17200 kg

Engine

• Effect168 kW
• Fuel typeDiesel

Collection

Other information

Epiroc SmartROC T35S, TMG169ED0182 med følgende oppsett:

Utstyr:
- Bormaskin Cop 2540EX
- Caterpillar C7.1 (168 Kw)
- Atlas Copco kompressor FAD 127l/s – 8,5bar
- Winsch
- Hydraulisk støtteben
- Dieselvarmer

Beskrivelse:
Maskinen bærer preg av Normal bruk i produksjonsborring og gir et godt førsteinntrykk.
Ingen nevneverdige lekkasjer på maskinen, litt svetting på hammer på de stedene det skal komme olje (Nakkesmøring)

Motor fungere perfekt.
Kompressor fungerer perfekt.
Hydraulikk pumper fungerer perfekt.
Støvsuger fungerer perfekt.
Maskinen er vedlikeholdt innenfor Epiroc sitt service program.
Maskinen har gått på Roc & Cop Care avtale hos Epiroc fra den var ny.
Hel og fin i karosseriet samt lakk i henhold til timer og alder.
Bananlenk virker tight og helt normalt slitt etter timer og alder.
Normal slitasje i bolter og foringer i bom, stikke etter timer og alder.

Maskinen har 9142 motortimer pr 19.01.2026.
Slagverkstimer er 3368 timer pr 19.01.2026.

Anbefalte utbedringer og påkost:

-Maskinen har en feil på Kabelnettet som må utbedres. Maskinen anbefales ikke å brukes med denne feilen.

-Undervogn har løse underruller og beltestyringer som bør utbedres umiddelbart. Kjeder og plater går en stund til.

-Mater: Glideskinner ser ok ut, borstødet har skader som bør utbedres.

Reparasjon av Kabelmatter, borrstø, understell, styringer, underruller, feste Lite El skap og div småtteri, hvis den utføres av Epiroc, er estimert til 350.000 - 450.000 for å få maskinen i god stand og klar for produksjon.

NB! Påkost er et estimat utført av Epiroc, men hverken NCC eller Epiroc kan garantere dette beløpet.

Befaring kan gjennomføres etter avtale, kontakt Martin Steen på martin@logpar.com for nærmere avtale.

Epiroc SmartROC T35S, TMG169ED0182 with the following setup:

Equipment:
- Drilling machine Cop 2540EX
- Caterpillar C7.1 (168 Kw)
- Atlas Copco compressor FAD 127l/s – 8.5bar
- Winch
- Hydraulic support leg
- Diesel heater

Description:
The machine bears the mark of Normal use in production drilling and gives a good first impression.
No significant leaks on the machine, a little sweating on the hammer in the places where oil should come (Neck lubrication)

Engine works perfectly.
Compressor works perfectly.
Hydraulic pumps work perfectly.
Vacuum cleaner works perfectly.
The machine has been maintained within Epiroc's service program.
The machine has been on a Roc & Cop Care agreement with Epiroc since it was new.
The bodywork is intact and the paint is in good condition according to hours and age.
Banana link seems tight and completely normal wear after hours and age.
Normal wear in bolts and bushings in boom, sticking after hours and age.

The machine has 9142 engine hours as of 19.01.2026.
Drilling hours are 3368 as of 19.01.2026.

Recommended repairs and additional costs:

-The machine has a fault in the cable network that must be repaired. The machine is not recommended to be used with this fault.

-Undercarriage has loose lower rollers and belt guides that should be repaired immediately. Chains and plates will last a while longer.

-Feeder: Slide rails look ok, the drill press has damage that should be repaired.

Repair of cable mats, drill stand, chassis, controls, lower rollers, attaching small electrical cabinets and various small items, if carried out by Epiroc, is estimated at 350,000 - 450,000 to get the machine in good condition and ready for production.

NB! The additional cost is an estimate made by Epiroc, but neither NCC nor Epiroc can guarantee this amount.

Inspections can be carried out by appointment, contact Martin Steen at martin@logpar.com for further arrangements.

English

Epiroc SmartROC T35S, TMG169ED0182 with the following setup:

Equipment:
- Drilling machine Cop 2540EX
- Caterpillar C7.1 (168 Kw)
- Atlas Copco compressor FAD 127l/s – 8.5bar
- Winch
- Hydraulic support leg
- Diesel heater

Description:
The machine shows normal signs of use in production drilling, creating a good first impression. There are no noteworthy leaks in the machine, with a small amount of sweat on the hammer where oil should be present (Neck Lubrication).

The engine is functioning perfectly.
The compressor is functioning perfectly.
The hydraulic pumps are functioning perfectly.
The vacuum cleaner is functioning perfectly.
The machine has been maintained according to Epiroc's service program.
The machine has been part of the Roc & Cop Care deal with Epiroc since it was new.
The bodywork and paint are in good condition given the hours of operation and age.
The banana link appears tight and exhibits normal wear and tear given the hours of operation and age.
Normal wear is seen in the bolts and bushings in the boom stick according to hours and age.

The machine has clocked 9,142 hours of engine operation as of 19.01.2026.
The machine had pounded for 3,368 hours as of 19.01.2026.

Recommended improvements and costs:

-The machine has a fault in the cable network that needs to be addressed. It is not recommended to operate the machine with this fault present.

-The chassis has loose lower rollers and track guides that should be remedied immediately. The chains and plates will continue to function for a while.

-Feeder: Sliderails look okay, but the drill support has damages that need to be addressed.

Repairs involving cable mats, drill support, undercarriage, controls, lower rollers, and the attachment of a small electrical cabinet, to name a few, if carried out by Epiroc, is estimated to cost between 350,000 to 450,000 to bring the machine to optimal working condition and production-ready.

Please note! This cost is an estimate provided by Epiroc, but neither NCC nor Epiroc can guarantee this amount.

Inspections can be arranged by appointment, feel free to get in touch with Martin Steen at martin@logpar.com for further details.